Printed circuit boards could single sided which means it has a layer of copper, a double sided which two copper layers are attached on each side or a multilayer which have alternating layers of substrate and copper. The multilayer PCB can allow a high component density due to having circuit traces on the inside part of layers or else it would rise up into the surface between the components. When it comes to TV Circuit Board, individuals must consult a professional to create them the device.
When you are doing the acid method, make sure to use ferric chloride. But you can still use other solutions like ammonium persulfate crystals. It does not matter what kind of chemical etchant to be used, all of it are still dangerous and needs to be handle with extreme caution. Read all important safety instruction s before doing the process of creating your very own PCB.
The circuit diagram must be aligned with the paper. The diagram must be facing towards the copper parts of the boards. Afterwards, iron it out. Cautiously place the iron in the top of the papers and on the board. Place it on the same area for about thirty to forty five seconds.
The UC etching method is used for reversal of circuit boards onto another board. This requires expensive materials that are not available in most areas. But the process is simple and can produce a much finer and complicated circuit laid outs than other methods.
Once finished, remove the boards from the insulator. Simply clean the sides where copper is with a photo revelator. Just rinse it distilled water to place in the acid bath. The parts and materials that were destroyed during the radiation of UV light would be etched on the acid directly.
Make sure the board is dry. Remove all moisture that is left on the board. Use a sponge or a napkin or just hang them up. It would not take longer than a minute that all the liquids are gone and removed. Do not force the moisture to be out or else the inks will be removed as well.
Get testimonials from other people. Companies that are in this business will offer some testimonials from previous clients to share their experience. You can call directly the people who have already purchase a device. They can recommend the same company if they were satisfied with the service. If not, they will simply tell you to move on and find another one.
Many people do experiment without any knowledge on how to perform the task. They are bound to fail. Therefore, to avoid and minimize the risk of failure when creating a circuit board, try to learn as much information as you possibly can. This will give lots of new ideas and new techniques on how to make things work.
Depending on the quality of the board and the quality of materials, the price will be much higher than expected. If you want to use a more complicated device, then it would be pricey. And if you chose only a circuit board that is for television, then it is just cheap.
When you are doing the acid method, make sure to use ferric chloride. But you can still use other solutions like ammonium persulfate crystals. It does not matter what kind of chemical etchant to be used, all of it are still dangerous and needs to be handle with extreme caution. Read all important safety instruction s before doing the process of creating your very own PCB.
The circuit diagram must be aligned with the paper. The diagram must be facing towards the copper parts of the boards. Afterwards, iron it out. Cautiously place the iron in the top of the papers and on the board. Place it on the same area for about thirty to forty five seconds.
The UC etching method is used for reversal of circuit boards onto another board. This requires expensive materials that are not available in most areas. But the process is simple and can produce a much finer and complicated circuit laid outs than other methods.
Once finished, remove the boards from the insulator. Simply clean the sides where copper is with a photo revelator. Just rinse it distilled water to place in the acid bath. The parts and materials that were destroyed during the radiation of UV light would be etched on the acid directly.
Make sure the board is dry. Remove all moisture that is left on the board. Use a sponge or a napkin or just hang them up. It would not take longer than a minute that all the liquids are gone and removed. Do not force the moisture to be out or else the inks will be removed as well.
Get testimonials from other people. Companies that are in this business will offer some testimonials from previous clients to share their experience. You can call directly the people who have already purchase a device. They can recommend the same company if they were satisfied with the service. If not, they will simply tell you to move on and find another one.
Many people do experiment without any knowledge on how to perform the task. They are bound to fail. Therefore, to avoid and minimize the risk of failure when creating a circuit board, try to learn as much information as you possibly can. This will give lots of new ideas and new techniques on how to make things work.
Depending on the quality of the board and the quality of materials, the price will be much higher than expected. If you want to use a more complicated device, then it would be pricey. And if you chose only a circuit board that is for television, then it is just cheap.
About the Author:
Your one-stop shop for TV circuit board parts and repairs is right here on the Web. To get instant access to the related website, go to http://www.tekbyus.com.
0 comments:
Post a Comment