Dielectric Strength or Hi Pot testings are completed by applying massive voltage against testing wire and ground, usually locomotive chassis. On the off chance that excess current spills or if a current arc happens, test show failure. Insulation Resistance tests give numbers showing resistance insulation. Data on how hipot testers function are found below.
High Pot can be AC or DC and done periodically, or at production line end, etc. Stress test result typically shows Pass Fail based on leakage current. For some systems, this may prove dangerous. Testing Medium Voltage Cable may also prove risky.
Dielectric strength presents maximum electrical field that pure material may withstand underneath ideal setting without tearing down or without experiencing failure with its insulating properties. Theoretical dielectric strength is material intrinsic property on bulk material and independent configuration material or electrodes with which field is put to use. This inherent dielectric withstand corresponds what is being measured using untouched materials under controlled laboratory settings.
In breakdown, electric field effectively frees bounded electrons. When applied electrical field is high, free electrons coming from background current radiation may be accelerated with velocities that may liberate additional bounded electrons upon meeting neutral atomic particles, molecules within avalanche breakdown. Breakdowns occur quite suddenly, typically nanoseconds, causing an electrical conduction path formation and disruptive discharge through material. Towards solid materials, breakdowns severely degrades, even neutralizing, its capability to insulate.
Regarding difference between insulation and dielectric testing, none exists. There should be no difference between insulation versus dielectric testing. Dielectrical strength simply shows how well insulator material. Now regarding testing, frequency test voltage should be determined by what voltage type insulating substance will expect during its operational life. Which means you should not DC withstand testing component that will be used for AC 5060 Hz applications.
While they are just two separate and very different procedures, these terms are wildly thrown around interchangeably in electrical industry. So you cannot easily rely on those names accurately describe what is being tested alongside how test was performed. For example, in Practical Guide Di electric Tests, where Di electric Tests in their definition is an Insulation Resistance tests HiPot tests combination.
Though, commonly, HiPot analyzer being utilized for Di electric Quality test would satisfy usage towards Insulation Resistance analyzation. Particular terminology utilization would truly rely upon trade you are working, managing. In the event that it truly matters, you have to read given methodology label itself.
An Insulation Resistance tests would always show DC. Di electric Strength tests would usually AC but could be DC. If one see if one other could go through elimination as they investigate similar things, electrical experiments were done before. Conclusion was that they are both needed as they provide different data as their results.
An emphasis on these tests interchangeability would trivial because, at the end of the day, most insulated materials go through both as it unwise generally to pigeon hole your substance product into using only one frequency, electrical transmission when most cases it will work for both assuming they have same amount. Using 48v DC system, generally using materials with secondary rating around 600v ac should suffice. Ultimately as long as one does not fail hipot, everyones happy regardless of insulated matter used.
High Pot can be AC or DC and done periodically, or at production line end, etc. Stress test result typically shows Pass Fail based on leakage current. For some systems, this may prove dangerous. Testing Medium Voltage Cable may also prove risky.
Dielectric strength presents maximum electrical field that pure material may withstand underneath ideal setting without tearing down or without experiencing failure with its insulating properties. Theoretical dielectric strength is material intrinsic property on bulk material and independent configuration material or electrodes with which field is put to use. This inherent dielectric withstand corresponds what is being measured using untouched materials under controlled laboratory settings.
In breakdown, electric field effectively frees bounded electrons. When applied electrical field is high, free electrons coming from background current radiation may be accelerated with velocities that may liberate additional bounded electrons upon meeting neutral atomic particles, molecules within avalanche breakdown. Breakdowns occur quite suddenly, typically nanoseconds, causing an electrical conduction path formation and disruptive discharge through material. Towards solid materials, breakdowns severely degrades, even neutralizing, its capability to insulate.
Regarding difference between insulation and dielectric testing, none exists. There should be no difference between insulation versus dielectric testing. Dielectrical strength simply shows how well insulator material. Now regarding testing, frequency test voltage should be determined by what voltage type insulating substance will expect during its operational life. Which means you should not DC withstand testing component that will be used for AC 5060 Hz applications.
While they are just two separate and very different procedures, these terms are wildly thrown around interchangeably in electrical industry. So you cannot easily rely on those names accurately describe what is being tested alongside how test was performed. For example, in Practical Guide Di electric Tests, where Di electric Tests in their definition is an Insulation Resistance tests HiPot tests combination.
Though, commonly, HiPot analyzer being utilized for Di electric Quality test would satisfy usage towards Insulation Resistance analyzation. Particular terminology utilization would truly rely upon trade you are working, managing. In the event that it truly matters, you have to read given methodology label itself.
An Insulation Resistance tests would always show DC. Di electric Strength tests would usually AC but could be DC. If one see if one other could go through elimination as they investigate similar things, electrical experiments were done before. Conclusion was that they are both needed as they provide different data as their results.
An emphasis on these tests interchangeability would trivial because, at the end of the day, most insulated materials go through both as it unwise generally to pigeon hole your substance product into using only one frequency, electrical transmission when most cases it will work for both assuming they have same amount. Using 48v DC system, generally using materials with secondary rating around 600v ac should suffice. Ultimately as long as one does not fail hipot, everyones happy regardless of insulated matter used.
About the Author:
Get an overview of the factors to consider when selecting a hipot tester supplier and more information about a reputable supplier at http://www.rossengineeringcorp.com/products/measurement/ac-dc-digital-hipots.html now.
No comments:
Post a Comment