The first thine which you should know in building electrical circuits for an electrical device are basic theories in electronics. Know the different components used and how to connect them properly to each other. Then study how to read and make schematic diagrams which are graphical representations of an electrical circuit using symbols and images.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Start with identifying the two types of electricity which are alternating current or AC and direct current or DC. The direction that electrical signals flows in AC is reversing constantly or alternating and the reversal rate is measured in Hertz. The flow in DC though is one direction from power source to ground and commonly found with batteries.
A circuit is closed when electric current is being allowed passage through a path to ground from power source which indicates a functioning device normally. While the open one has broken the path and prevents movement when a machine is turned off. This is done using a switch so you can alternate between them rather than removing its source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Adding resistance into circuits is done with resistors and they reduce current flow and are also available in a variety of values measured with ohms. They have wattage ratings also and their value is indicated by colored bands around their body. You could learn reading these bands or look up for graphs that helps in calculating their values.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
Doing so is essential when there is a particular device you want to make but is still confused with some parts of the process. This might be something a little advance such as voltage divider which produces an output that is a portion of its input. But learn or review first the theories in basic electronics to understand better the more advanced stuffs.
Start with identifying the two types of electricity which are alternating current or AC and direct current or DC. The direction that electrical signals flows in AC is reversing constantly or alternating and the reversal rate is measured in Hertz. The flow in DC though is one direction from power source to ground and commonly found with batteries.
A circuit is closed when electric current is being allowed passage through a path to ground from power source which indicates a functioning device normally. While the open one has broken the path and prevents movement when a machine is turned off. This is done using a switch so you can alternate between them rather than removing its source.
Components creates resistance if current pass through from a positive voltage to a ground and a short circuit happens when these two are connected directly. Avoid this direct connections because they would result in breaking, overheating, explosion or fire. Putting only a switch between them is not enough and other parts are needed for additional resistance.
Wiring things together could be done with two ways that are called series as well as parallel and the former indicating that every component is wired after each one. While the latter would indicate that the parts were wired next to the other which makes electricity simultaneously pass them. Both ways can be used together when you build circuits.
Adding resistance into circuits is done with resistors and they reduce current flow and are also available in a variety of values measured with ohms. They have wattage ratings also and their value is indicated by colored bands around their body. You could learn reading these bands or look up for graphs that helps in calculating their values.
Capacitors are components which stores electricity then when it drops, discharges them and Farads is used to measure them with common units being picofarad, microfarad, and nanofarad. The capacitor types most used commonly are ceramic disc as well as electrolytic. The former is non polarized while the latter is polarized needing one leg to properly connect with the corresponding one.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
0 comments:
Post a Comment